How to Manage VoIP Supplier Rate Decks in MediaCore Class 4 Softswitch 5.2

To manage supplier rate decks in MediaCore Class 4 Softswitch 5.2, select the correct company and tariff context, choose a processing rule and upload type, map the file through a rate template, and check processing results. After upload, launch the comparison to review price changes, billing parameters and effective dates. Receiving a file is not the same as successfully processing it.
MediaCore Class 4 Softswitch is Speedflow’s Class 4 softswitch for wholesale VoIP, with routing and integrated billing. In MC 5.2, our Rate Management updates bring rules, direct uploads, guided templates and clearer error diagnostics into a more structured operational workflow.
What is a VoIP supplier rate deck?
A supplier rate deck is a price list describing the destinations or prefixes a carrier charges for, together with the applicable rates and commercial conditions. Depending on the supplier’s format, it may also include effective dates and billing parameters. It is operational data, not just a price announcement: an incorrect mapping or update scope can change how a rate is interpreted.
Before uploading a file, identify its supplier, intended tariff, currency, update scope and effective-date convention. These are review checks for your team, not a claim that every item is automatically validated by MediaCore Class 4 Softswitch.
1. Find the right processing rule
MC 5.2 combines Processing Rules and Company Rules in a single Rules tab. A tariff filter lets you narrow the view to the relevant context instead of moving between separate rule lists.
Start with the tariff the incoming file is intended to update. Confirm that the selected rule belongs to the expected company and matches the supplier’s file format. A familiar filename is not enough to establish that a spreadsheet follows the same layout as last month’s file.
2. Choose the intake method and upload type
MediaCore Class 4 Softswitch 5.2 supports direct file uploads through the interface alongside the existing email-based intake. A manual upload lets you choose both the processing rule and the upload type: Full A-Z, Incremental or Full Country.
| Decision | What to check |
|---|---|
| Direct UI upload | Select the intended rule and upload type for this file. |
| Email intake | Check the subsequent processing result; receipt alone is not success. |
| Full Country | Confirm the file contains the intended replacement data for the affected country. |
| Full A-Z or Incremental | Verify replacement, retention and closure behaviour against your configured rule before production use. |
Full Country deserves particular care. In MC 5.2, this upload type closes out old codes for the affected country and replaces them with the new file’s contents. A partial list should not be treated as a complete country replacement without confirming that this is the intended result.
The release notes name Full A-Z and Incremental as available options but do not define every edge case for omitted rows or code closure. Do not infer those behaviours from the option names alone.
3. Build the template around the actual file
The guided template workflow takes you through uploading a file, previewing its first rows, choosing the header row and mapping columns to fields. Use the preview to distinguish the actual data table from introductory text, supplier contact information or notes above it.
Check the mapping against sample rows, not only column titles. As operational checks, confirm that prefixes retain their intended representation, numeric values use the expected units, and dates are interpreted consistently. If a supplier changes its layout, review the template before relying on the previous mapping.

4. Check processing status and investigate the failed line
MC 5.2 separates email intake and rate processing into independent stages. This distinction matters when troubleshooting: a received message does not establish that its rate file has been processed correctly.
The Rates page provides detailed processing errors, including the exact line that failed. A status filter helps locate entries in a particular state. Start with the reported line, then inspect its source values and the mapping used to interpret them.
For example, a supplier might move a date column while leaving the filename unchanged. Treat this as an illustrative investigation scenario, not a documented MediaCore Class 4 Softswitch error message. Compare the file with the template, correct the identified problem, and review the processing result again. Before resubmitting, establish whether any part of the previous attempt was applied; do not assume automatic rollback or duplicate protection.
5. Run the comparison after upload
Price comparison in MC 5.2 is initiated by pressing a button after upload. The comparison highlights price increases and decreases, changes to MC/CI/FT values, and effective dates that provide less than seven days’ notice.
MC 5.2 also handles files with multiple MC/CI/FT values for the same direction that take effect on different future dates. Check each dated change rather than reducing the review to a single current price.
A short-notice warning is a review signal. It does not by itself establish automatic rejection, compliance with a supplier contract, or a mandatory approval gate before activation. Those operational decisions need to follow your agreed process and verified system configuration.
A practical pre-production test
Use a controlled test tariff and a small representative file before applying a new supplier format to production. The following is a suggested acceptance test, not a report of a test already performed.
- Confirm that the selected company, tariff and processing rule match the test file.
- Preview the file and verify the header row and column mappings.
- Check the intended upload scope. For Full Country, inspect both the closing of old codes and the replacement contents.
- Include a deliberately invalid row in the test data and verify that the diagnostic identifies the failed line.
- Launch the comparison and inspect a price increase, a decrease and a billing-parameter change.
- Include future-dated changes and check the resulting dates; test a short-notice case separately.
- Confirm the processing outcome and the actual tariff contents before considering the test complete.
- Repeat the relevant task using the intended operational role, not only the Owner account.
Who can access Rate Management?
In MC 5.2, Rate Management access is restricted to the Owner role by default. Custom roles can be granted specific visibility into the section. Check the permissions available to the people who handle rate files; visibility should not be treated as proof of approval rights or every possible editing permission.
Frequently asked questions
Can I upload a supplier rate file without email?
Yes. MC 5.2 adds direct UI uploads with selection of a processing rule and upload type. Email-based intake remains available.
Does comparison start automatically when a file arrives?
No automatic-on-arrival behaviour is described in the MC 5.2 release notes. The documented comparison is started with a button after upload.
What does Full Country do to existing codes?
It closes out old codes for the affected country and replaces them with the new file’s contents. Verify that the replacement file has the intended country coverage before using this mode.
Where do I investigate an unsuccessful import?
On the Rates page, use the status filter and detailed processing error, including the failed line. Check the source data and template together rather than uploading the same file repeatedly without investigating.
Review your supplier workflow with MediaCore Class 4 Softswitch
Bring a representative supplier file, its update scope and your effective-date requirements to a discussion with our MediaCore Class 4 Softswitch team. Confirm the capabilities available in your deployment and the handling of your specific rate format. For the wider platform evaluation, use our Class 4 softswitch checklist.
